Air conditioning in Fort Myers is an essential element in any home. Whether you choose a full size unit or a simple window unit, an air conditioner helps to combat those warm sticky days of summer. The last thing you want is for your air conditioning to stop working during a Florida summer and one of the best ways to avoid this is with regular maintenance.
The thermostat is the control panel for the entire cooling system. Whatever temperature it is reading will determine how long the system runs. But, it also needs a target temperature programmed in to know when to stop. If the system is set to cool until 60 degrees, it will never stop. The wires running from the thermostat to the unit should also be checked for any fraying or loose connections. Many of today’s thermostats are programmable with different cooling times to optimize the system and save on energy costs.
The inside part of the system is the evaporator coils and the fan. Coolant travels into the coils and cools them down. The fan blows circulated air from the house over the coils, cooling it and sending it back into the house. As the air warms in the house, it rises and travels through vents higher on the walls. These warm air returns funnel the air back down to the fan where the cycle starts again. But, as the air flows through the house it picks up dust and dander and that can gather on the coils. As this debris builds on the coils, the coolant has a tougher job cooling the air as it flows past. Regularly changing the air filters helps reduce the dust that flows over the coils.
As the coolant leaves the house, it is carrying the heat from the indoor air with it. The first part of the outdoor unit is the condenser. As the coolant leaves the house, it is warmed up and converted to a gas. The condenser fan cools the coolant down and dissipates the heat out into the environment. The condenser also changes the coolant back to a liquid state. Like the evaporator coils, the condenser has coils that can get dirty and make the system work harder. A periodic spraying of the coils can keep them clean and free of debris that can damage the system.
As the coolant continues its journey, the compressor squeezes the liquid even further. As the pressure builds, heat energy is given off by the liquid. This heat is also dissipated by the exterior fan. The coolant travels into the house where it flows through the evaporator, but the pipes leading back inside need to be well insulated so the coolant does not heat up before getting inside. Also, as the ambient humidity outside condenses on the pipes, it can begin to freeze and slow down or stop the path of the coolant. The biggest enemies of the outside unit as a whole are the bushes and leaves around it. These items can block the flow of the hot air away from the unit.
Many HVAC companies have great maintenance programs. They will come out and clean the system as well as check the coolant levels. But, homeowners that follow these tips can keep their air conditioning in Fort Myers running smooth and free of major problems all year long.
Fences are built as a barrier between properties. They are a friendly way of reminding your neighbors and others what’s on your side and what’s on theirs. However, your fence looks less formidable when there are weeds and other greenery growing over it. It may come across that you do not care what your yard looks like and that you don’t take your property seriously. Plus, such greenery could damage your fences. Fortunately, chain-link fences are fairly durable, yet you should clear the growth on them anyway. Follow these tips and suggestions for a brush-free area around your chain-link fence.
Overgrowing grass can be unsightly on a chain-linked fence. You’ll need to get at the grass with your hands. You can make this task easier by applying these tips. Wait for a hotter day and pour undiluted white vinegar into a spray bottle. Then spray the grassy areas by the fence. Give the vinegar 3 to 5 days to work its magic. The grass should die. If you notice the grass is still thriving, apply more vinegar. If you would prefer something stronger, you may apply an herbicide. When the grass is dead, don your garden gloves and pull out the brown blades. Collect the blades in a compost bin or trash can. It may be helpful to use a spade to pull out these pieces of grass. Next, do what you can to prevent the regrowth of grass. Apply mulch in 3- to 4-inch layers around the base of the fence. Keep in mind that the mulch should stand 1/2- to 3/4-inch away from the fence. If that doesn’t suit you, place black plastic around the fence’s base to act as a barrier against sunlight and water.
Weeds are another threat to chain-link fences, so they should be dealt with accordingly. Consider using herbicides. Start out by directly spraying the fence with a broadleaf herbicide. It should contain glyphosate. The great thing about selective herbicides is that they only target weeds without killing off grass and other greenery. Follow directions to know how to do this properly. Perhaps your weeds are coming from trees and their branches spanning along the fence line. If that’s the case, cut out these trees. Again, find an herbicide that contains glyphosphate; triclopyr is another excellent alternative. Spray the herbicide on what’s left of the tree. Then you should paint diesel oil or mineral oil over the stump. This keeps weeds from growing back. Another idea is to purchase a sterilant to apply around the fence to prevent the growth of weeds. Aim for early spring or late winter to apply the sterilant. Again, read the directions in full detail to know how to properly use this product.
Some homeowners are not thrilled about using chemicals on their yards. If you’re one of these folks, consider these natural solutions. First, put on gardening gloves and go at the weeds growing on the fence with gardening shears. Put the weeds in a plastic bag; they should not be left on the ground because the spores can spread and create new growth. Now go through the bottom of the fence with a weed trimmer or garden shears. Afterwards, you should spray the ground near chain-link fences with straight white vinegar. The vinegar ought to kill off the weeds if it does not rain in the next day or two.
As any homeowner can tell you, your foundation is critical to a house’s well-being. After all, a foundation is what a home is built on. When it fails, your whole house can suffer. A faulty foundation can cause your structure to sink or crumble. While a home inspector or another professional has a better eye for foundation issues, you as a homeowner should be able to notice a few signs of foundation failure. Even the smallest indications could lead to big trouble in the end. So keep your eyes peeled so you can nip these problems in the bud. Read more to know what these warning signs are.
Go around your home and check out the doors and windows. Open and shut the doors and windows, looking for signs of difficulty. The windows and doors should tightly shut at the binding. Doors and windows that stick are a bad sign. Also be on the lookout for doors and windows that are uneven or seem to be at a slope. If the doors do not fit within a frame, that could be an indication that the foundation is shifting. Cracked joints surrounding doors and windows are not good either.
Cracks and splits may be seen on your walls and ceilings. This is due to extra pressure from the foundation shifting. Cracks are usually prevalent in the interior, at the corners and where 2 walls may merge together. If you have a fireplace, there may be cracks in or surrounding it. You may have wallpaper in your house and see that it is separating. Know that this is a kind of foundation damage since the walls are being moved. Loose nails may also come out of your walls. Last, cracks may also be present on the exterior and around the porch.
Naturally, a flawed and uneven foundation may affect a home’s flooring. You may notice a slope in the ground due to foundation shifting. Put a ball on the floor and see if it rolls to test this theory. Also try rearranging furniture and identify wobbling. A level is a sure way to determine the flatness of a floor. Bumps may also be a sign of a poor foundation. Another piece of proof in the floor is cracks, particularly where the floor touches the walls. Cracks in tile are common, as are cracks in the basement, and although this is not uncommon in concrete, you should be worried when water leaks occur.
Investigate your home’s exterior to pinpoint foundation damage. Read more to identify the signs. If your house has a brick exterior, you may note step-like cracks in the mortar. For really serious cases, the brick may be cracking as well. Check out the roof also. Leaky roofs could be telling, but you should discover more about the age of the roof and what material it is made out of. However, frequent leaks on good quality roofs may indicate a poor foundation. Locate leaking in the areas where the roof meets the walls and where you’ve seen cracks in your interior. Furthermore, you should look outside to see what may cause the flaws in the foundation. Standing water following a rainfall can be a cause. Foundation problems may also stem from nearby bushes and trees that absorb too much water from soil and cause shifting in the foundation.
A Minneapolis roofing company will have experts who are ready to put on your new roof or replace your existing roof. They should be licensed, bonded, and insured. Asking to see their credentials shouldn’t be a problem. If producing proof of their credentials is a problem, you should look for another roofing company. There are roofing companies that either specialize in a specific type of roofing material, or can repair or put on any type of roof you want. A flat roof requires a roofing system that is very different from a pitched roof. If you need your flat roof upgraded or replaced, there are a few choices available for homeowners.
Tar paper used to be the waterproof material used in flat roofs until it was replaced with membranes made of fiberglass. This is a type of flat roof that is commonly called a built-up roof, or a BUR. Typically, three layers of fiberglass membrane are used with hot tar in between each layer, and finished with a topping of smooth river rocks. Rock doesn’t burn, so it is superior to wood in case of a house fire, and looks good if you have windows that will be positioned where the occupants will see the roof. Because of the weight of this type of roof, the roof supports may have to be bolstered.
Another type of flat roof material is rolled roofing that serves as an ice and water barrier and is mineral based. There are two types of mineral-based rolled roofing: torch-down and peel and stick. Torch-down roofing requires heat for the roofing material to adhere to the roof and can be a potential fire hazard. The peel-and-stick type is very easy to install and will reflect some heat with its lighter colored surface.
Ethylene propylene diene monomere is 100% rubber and is also known as EPDM. When you look at it, you might see similarities between it and the inner tube of your bike tires. It is manufactured to be impervious to sun damage. You can glue this type of Minneapolis roofing material to the roof, use fasteners to attach it to the roof, or cover it with decorative stone to hold it down. This type of roofing material comes standard in black, but can be purchased in a light color, which is more expensive, but recommended in areas where the sun shines most of the year.
People use their basements for many things. Some use the space for storage while others create a separate living space. Others combine these two options for a spare rooms as well as additional storage. Whatever the use is, basement waterproofing in Milwaukee, WI, will prevent water damage to both your home and your belongings.
The first step to make sure that your basement remains dry is to evaluate the surrounding grounds. The land around your home should slope away from the house so that all water will drain away from the foundation. Oftentimes backfilled dirt will settle lower than the surrounding dirt causing water to collect around the foundation. This can cause water to seep into your basement. To correct this you will need to add dirt to the ground around your foundation until a downward slope is created. Also, all gutters should be regularly cleaned and the downspouts should release water at least five feet from the home. Finally, shrubs, plants, and flowers should be placed about a foot from the foundation as the roots can create an easy path for water to run against the foundation.
If you still have some minor leaks appearing along your basement walls there are products that you can purchase that will seal the walls off. Some of these products are more of a sealant and will work where there is currently a leak. Other products will prevent against future leaks as a waterproofing paint or primer. You should also immediately repair any holes or cracks in your basement walls or along the pipelines. Finally, if your home does not have a sump pump, installing one could save you from disaster in the case of a flood. If you need help with waterproofing in Milwaukee, WI, there are many companies that are capable of completely waterproofing your home.
When homeowners try to keep their Philadelphia glass windows clean on a regular basis, it can get rather tricky. With the changing seasons, it’s difficult to keep up. Every homeowner would agree that if they could find ways to keep their windows cleaner for longer, it would make their lives much easier. That being said, luckily there are a few tricks that the average homeowner doesn’t know about. Keep reading to learn some little-known tips for keeping that glass sparkling clean with minimal work.
This is one of the best tips for homeowners as it is a simple, fast, affordable way to get a streak-free shine on a moment’s notice. Automobile glass wipes are quick, effective, and disposable. Keep a package tucked away in your main window rooms and pull it out at a moment’s notice. Just a few wipes and you’ve got a streak-free window shortly after the tots have smudged it up with their hands. It beats getting out the expensive, messy cleaners and works better by leaving a streak-free clean. Find them in the automobile section.
Upkeep is really the trick to keeping clean windows. Keeping a squeegee on hand for those rare rainy days or especially for the shower doors will help to resist residue buildup and provide a cleaner finish for longer periods of time. Simply squeegee after showers and you can skip the heavy duty cleaning almost indefinitely. Squeegees are inexpensive to buy, small to store, and easy to keep on hand. There is no reason to not instigate this practice in your home, as it will help you to keep virtually any glass surface clean if used regularly.
This might sound rather strange; however, it really does work. Streaks are an issue for anyone cleaning glass. They just happen. This is especially true if cleaned in direct sunlight. Cloudy days offer a break that should be taken at any possible opportunity that will reduce the development at streaks almost definitely. This is a great way to clean if you run out of those automobile wipes that were mentioned earlier. Indeed, those who clean their Philadelphia glass regularly and use these little tips and tricks on a regular basis are those who will have cleaner windows for longer.
You do not wish to ruin your lawn by driving upon it frequently, nor do you want to be late for work because you have to park your vehicle in a mud pit. As a result, most homes have a paved driveway offering a solid surface for your vehicle. A paved driveway also makes clearing snow in the winter easier, as well as washing away dirt and debris. Plus, kids can use the area for basketball or bike riding fun. But which choice is best from your driveway paving company: concrete or asphalt? You may find that it really comes down to a matter of preference. Read the rest of this entry »
The many advances in modern technology have helped to bring convenience and efficiency to the modern lifestyle. There are many things that make your life easier than the lives your ancestors lived. From modern heating and cooling systems, mass-produced food, modern health care, transportation services, automobiles, and electronic information, to modern plumbing, your life is significantly easier than the life that your ancestors lived.
While simply having running water is a great convenience, heated water is even more luxurious. If you have had a conventional water heater in the past, you may want to look at some of the newer advanced options in water heating that have become popular recently. In particular, you may want to learn about solar water heaters. If you decide to buy a solar water heater in Reno, you should contact your local plumber or water heater supplier for more information today.
In the United States today, there are two standard types of water heaters. First, there are heaters that are powered by electricity. Second, there are water heaters that are powered by natural gas or liquid propane. Within these two categories, there are many models and styles. Each comes with its own set of advantages and disadvantages. Some heaters are capable of warming massive amounts of water, and others are able to heat a small amount of water right as it is needed. Some are more efficient and others use more fuel or energy. Some heaters cost much more than others do, and yet they provide increased performance or efficiency.
If you are tired of paying money each month to use hot water, you may be looking for a better solution. While you could choose to install a bunch of on-demand heaters, you will still be reliant on electricity to provide the energy you need to heat the water. There is a way that you can have hot water without having high associated energy costs. If you choose to install a quality solar water heater, you can enjoy hot water and a considerable savings in energy costs.
Solar water heaters have some major advantages over traditional-style heaters. First, solar water heaters can be used without power or other energy dependence. That is a huge advantage if you live remotely, or if you are trying to live without dependence to a power company or fossil fuels. Another advantage of using a solar water heater is that you will drastically reduce the greenhouse gas emission of your home. This will help the environment, and will be an example of responsible living to your friends and family as well. If you are interested in a solar water heater in Reno, you should contact your local plumbing company and see if they will install one for you today.
If you are putting in a new walkway or driveway, then you will want to consider using a concrete company to help you install it. While there are many different paving materials that you can use in your application, concrete is one of the best. If you are considering concrete in Minneapolis, you should read this short article for more information on the subject.
Concrete is a very strong and durable paving material. While there are many suitable materials, most of them have a major disadvantage. Natural stone paving materials such as cobblestone or quartzite flagstone are durable and beautiful, but they are highly cost prohibitive. They have a higher material cost, as well as a higher installation cost. Together, this makes natural stone an expensive choice when compared to concrete. Other paving materials such as asphalt may offer a slight reduction in initial cost, but are often less durable than properly installed concrete is.
If you are looking to have concrete installation performed in your yard, you will want to find a contractor who knows how to perform the job correctly. If you ask around, you will find someone who has had a good experience with a concrete contractor. You should get the contact information for that contractor and do some investigative work before hiring them. Make sure they have the skills and experience to do a good job on your project, and ask for some customer referrals as well. This will help you know how jobs have gone for other customers. It is important to find out how well you will be treated as a customer, and how fast and thorough the contractor is.
Invite the contractor to come inspect your project and submit a bid. This will give you the chance to work with him or her, and it will help you see if you are a good fit. Look for someone that you communicate well with, and make sure they are clear with you about the time frame that you will wait until the project is complete.
When the concrete crew comes to begin work on your house, they will begin by removing the old paving surface if there is one. If there isn’t, they will then start to prepare the earth bed that the concrete will lay on. It is crucial that concrete is given a solid bed that will provide support. If it is not supported sufficiently, concrete will crack, shift, or break. The crew will then make a form along the borders of the concrete slab that will contain the liquid concrete until it cures. Next, steel reinforcing is added, and tied into position so that it will be centered in the concrete where it will be strongest. The concrete is then poured and finished. If you are looking for concrete in Minneapolis, you should contact your local contractor to get started right away.
Every building in a city is required to have a foundation. Even if the area you live does not require that you have a foundation, it is greatly recommended. A foundation is the most important part of the home, and when it is damaged, it cannot do its job properly. It is vital that you get Dallas foundation repair as soon as you notice a problem with your foundation. If you don’t, you can suffer some serious consequences and some damage that will become extremely expensive.
All buildings start as a design. This means that before anything is actually built, the engineers know exactly how large the building will be. The foundation is designed in regards to the structure of the building. For example, the foundation of a skyscraper will go much deeper into the ground than a foundation for a home. This is because the larger building requires more support. Shallow foundations are usually only about a few feet into the ground. They are also called footings. Deep foundations go much farther into the ground. A monopile foundation is a large, single form that will support all aspects of the building.
A foundation serves two main purposes. These are both very important things, and without one or the other, the building will fail. The first purpose is in support. The weight of the building needs to be supported in some way, because the building cannot support itself, and the topsoil on the ground cannot support it either. The foundation takes the weight of the building and puts the support somewhere else, such as bedrock underneath the ground.
The other purpose of the foundation is keeping the building steady. The soil will always move over time, but the foundation will not. Without a foundation, a house can fall apart. The walls will separate from each other and the floor will crack. The entire house can split apart as the house moves. The foundation gives the building a firm base to stay on, so while the soil underneath the home moves, the home will stay where it is. When the foundation is broken, it cannot serve these purposes. This is what makes Dallas foundation repair so important.